SikaTop® Seal-107 IN
TWO PACK POLYMER MODIFIED CEMENTITIOUS WATERPROOFING SLURRY AND PROTECTIVE COATING
SikaTop® Seal-107 IN is a two-part acrylic polymer modified cementitious liquid applied waterproofing coating system. It comprises of a liquid polymer and a cement based mix incorporating special admixtures. It is applied to concrete and mortar to prevent water infiltration.
- Easy to apply by brush or in thin trowel applications
- No additional water is required to make the slurry
- Pre batched components with consistent quality
- Hand or Spray applied
- Easy and fast mixing
- Increased frost and salt resistance
- Very good adhesion with sound and prepared substrates
- Protects concrete against water penetration, chloride and carbonation
- Non-Corrosive to steel and iron
- Approved for potable water contact
- Flexible enough to bridge hairline crack
- No drying or shrinkage cracks if used according to instruction
- Good resistance to abrasion and erosion
- Bonds well to all damp substrates
- Can be applied on reinforced concrete, mortar or masonry
Usage
- Interior and exterior waterproofing and damp-proofing of concrete, cementitious rendering, brickwork and blockwork
- Protection of concrete structures against the effects of de-icing salts and freeze-thaw attack
- Exterior waterproofing of basement walls in new construction and refurbishment
- Pore / blowhole filling
- Cementitious waterproofing for drinking and portable water, wet room and swimming pool system
- Rigid waterproofing of basement walls in new construction and refurbishment
- Sealing fine “hairline” cracks in concrete structures not subject to movement
- Sealing internal basement walls against dampness
- Levelling mortar for concrete repair works
- Potable concrete water tanks / reservoirs
- Terraces and balconies
- Basement and Retaining walls
- Swimming pools, fountains and water bodies
- RCC gutters, drains and planter boxes
- Bathroom / toilets / Sunk slabs
- Lift pits / Sump
- Seawalls
Advantages
- Easy to apply by brush or in thin trowel applications
- No additional water is required to make the slurry
- Pre batched components with consistent quality
- Hand or Spray applied
- Easy and fast mixing
- Increased frost and salt resistance
- Very good adhesion with sound and prepared substrates
- Protects concrete against water penetration, chloride and carbonation
- Non-Corrosive to steel and iron
- Approved for potable water contact
- Flexible enough to bridge hairline crack
- No drying or shrinkage cracks if used according to instruction
- Good resistance to abrasion and erosion
- Bonds well to all damp substrates
- Can be applied on reinforced concrete, mortar or masonry
Packaging
Part A: 5.0 kg container
Part B: 20.0 kg bag
Part (A+B) : 25 kg ready to mix units x 2 sets
Colour
Part A : White Liquid Part B : Grey Powder Part A+B : Cement Grey slurry
Product Details
APPROVALS / CERTIFICATES
- SGS Certificate - Free from acute lethal toxicity as per IS 6582
- CFTRI Certificate for repeated use with aqueous foods / water as per USFDA 175.300
Composition
Part A : Liquid polymer & additive Part B : Portland Cement with selected aggregate and additive
Shelf life
12 months from date of production
Storage conditions
Product should be stored in original, unopened, undamaged and sealed packaging in dry and cool conditions. Liquid component must be protected from frost.
Density
Fresh Slurry : ~ 2.0 kg/ liter at +27°C
System Structure
Concealed System:
Layer thickness : 1.5 mm Base Coat : 1 x SikaTop® Seal-107 IN Fabric reinforcement : 1 x Sika® Fab-1 Top Coat : 1x SikaTop® Seal-107 IN + Separation Layer UV-protection : Screed concrete with slope ( min avg. Thickness 50 mm )
Compressive Strength
3 days | ≥ 2 N/mm2 |
28 days | ≥ 20 N/mm2 |
At temperature +27°C
Tensile Strength
≥ 4.5 N/mm² after 14 days exposure | (ASTM D 2370) |
Tensile Adhesion Strength
≥ 2 N/mm² (Concrete Failure) | (ASTM C 882) |
Application
Mixing Ratio
Part A : Part B = 1:4 (By weight)
Layer Thickness
1.5 – 2.0 mm average thickness with Sika® Fab-1
Ambient Air Temperature
+10°C min. / +40°C max.
Substrate Temperature
+10°C min. / +40°C max.
Pot Life
~ 40 minutes at +27°C. Pot life will be shortened at higher temperatures.
Waiting Time / Overcoating
Waiting Time The waiting time between consecutive coats is 2 - 6 hours (at +30°C).
Overcoating For overcoating with cementitious materials, allow the second coat to harden for at least 3 days prior to overcoating. For use in water-retaining structures or for applying renders over it or for overcoating with non-cementitious materials, please contact Sika Technical Services.
Consumption
Layer | Product | Consumption |
1 | SikaTop® Seal-107 IN | ~ 1.5 kg/m2 |
2 | Sika® Fab-1 | ~1 m2/m2 |
3 | SikaTop® Seal-107 IN | ~ 1.5 kg/m2 |
- Actual site consumption is dependent on the application area, substrate roughness, surface profile and thickness required
- Depending on the type of application, 2 coats are always required.
- For waterproofing upto 1m head pressure ~1.5 kg/m2 per coat.
- Above 1m head pressure ~ 2 kg/m2 per coat.
- Three coats may be required in areas of extremely high infiltration.
- Normally 3 kg/m2 of SikaTop® Seal-107 IN is sufficient to cover one square meter area. On well prepared smooth substrate the consumption would be less.
- Usage of Sika® Fab-1 is optional. For application areas, where Sika® Fab-1 is must, please consult Sika Technical Services.
EQUIPMENT
SikaTop® Seal-107 IN must be mechanically mixed using a forced action mixer or in a clean drum using a drill and paddle (max. 500 rpm). A normal concrete free fall mixer is NOT suitable.
MIXING
The consistency of the mix can be altered by reducing the amount of Component A (liquid) to be used. Under normal circumstances, when the full quantities of both components are mixed together, a slurry consistency will result. For trowellable consistency use only 90% of component A. Mix in a clean container by slowly adding the powder component to the liquid component and stirring with low speed mixer (max. 500 rpm). Mix for 3 minutes until free from lumps.
APPLICATION
The surface must be pre-wetted to a saturated surface dry condition with no standing water at time of application. While the surface is still damp from saturation, apply the first coat and leave to harden for 2-6 hrs at +30°C before applying the second coat.
As a slurry Apply the mixed SikaTop® Seal-107 IN by hand using a hard plastic bristled brush or broom. Applied in the same direction. Apply the second coat of SikaTop® Seal-107 IN in crosswise direction to the first application as soon as first coat has hardened.
As a mortar SikaTop® Seal-107 IN is applied by trowel (e.g. for a smooth surface finish), the product must be mixed with a 10 % reduction of part A. Apply the second coat of SikaTop® Seal-107 IN as soon as the first coat has hardened. For pore / blowhole filling, tightly trowel into the pores / blowholes of the surface. For floor applications, to avoid risk of damage to the first coat, it is recommended that the second coat be applied before 24 hours. If the second coat is applied 12 hours or later, the first coat shall be slightly prewetted, preferably by using a fine spray. After the second coat has been applied, a better finish can be achieved by rubbing down with a soft, dry sponge. For more details, please contact Sika Technical Services.
CURING TREATMENT
For cement based products, proper curing is important for minimum 3 to 5 days. Protect newly applied SikaTop® Seal-107 IN against direct sunlight, wind, rain and frost to ensure full cement hydration and minimize cracking. Use polythene sheeting or similar approved methods.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with clean water immediately after use. Hardened / cured material can only be removed mechanically.